Brand Name: Simpson Strong-Tie
*Height: 18 in.
*Width: 1.25 in.
*Gauge: 20 Ga.
*Material: Galvanized Steel
*Product Type: Strap
*Joist Fasteners: 10d
*Straps are designed to transfer tension loads in a wide variety of applications
* These straps are designed for use on the edge of 2x members with a nailing pattern that reduces the potential for splitting
14-Gauge 12 in. x 8 in. T Strap *Material Type: Galvanized Steel *Product Type: T Strap *Assembled Height: 12 in. *Assembled Width: 2 in. *Gauge: 14 Ga. *Joist Fasteners: 16d *12 in. x 8 in. x 2 in.* Simpson Strong-Tie straps and plates join and reinforce joints with simple, versatile solutions for a wide range of connections. Available in many lengths, widths and thicknesses, straps can be used on the wide or narrow face of lumber for light repairs or heavy-duty projects. Many straps are designed to be used back-to-back on a piece of lumber without fastener interference.
Brand Name: Simpson Strong-Tie
*Height: 7.81 in.
*Width: 1.56 in.
*Gauge: 18 Ga.
*Material: Galvanized Steel
*Product Type: Joist Hanger
*Joist Fasteners: 16d
*7-13/16 in. H x 1-9/16 in. W x 1-3/4 in." D
* This hanger features patented double shear nailing which distributes the load through two points on each joist nail for greater strength
* It also allows for the use of fewer nails, faster installation and the u
Brand Name: Simpson Strong-Tie
*Height: 4.75 in.
*Width: 1.56 in.
*Gauge: 18 Ga.
*Material: Galvanized Steel
*Product Type: Joist Hanger
*Joist Fasteners: 10d
*Minimum Heel Height: 4.4375 in.
*4-3/4 in. H x 1-9/16 in. W x 1-3/4 in. D
* For 2 in. x 6 in. joist
* This hanger features patented double shear nailing which distributes the load through two points on each joist nail for greater strength
* It also allows for the use of
Brand Name: Simpson Strong-Tie
*Height: 2 in.
*Width: 6.56 in.
*Gauge: 18 Ga.
*Material: Galvanized Steel
*Product Type: Joist Hanger
*Assembled Width: 3-9/16 in.
*Assembled Height: 4-3/4 in.
*Minimum Heel Height: 4-3/8 in.
*Joist Fasteners: 16d
*Use all specified fasteners
* Use hot-dip galvanized (HDG) nails with ZMAX and HDG connector products
* Use Type 316 stainless-steel nails with our stainless-steel connector products
* Nails must be driven at an angle through the joist or truss into the header to achieve the table loads
* Not designed for welded or nailer applications
* 16d sinkers (0.148 in. dia. x 3 1/4 in. long) may be used where 10d commons are specified with no reduction in load. Where 16d commons are specified, 10d commons or 16d sinkers (0.148 in. dia. x 3-1/4 in. long) may be used at 0.85 of the table load
* With 2x carrying members, use 10d x 1-1/2 in. nails into the header and 10d commons into the joist, reduce the load to 0.64 of the table value
Brand Name: Simpson Strong-Tie
*Height: 16.69 in.
*Width: 3.94 in.
*Gauge: 7 Ga.
*Material: Galvanized Steel
*Product Type: Column Base
*For 4 in. x 4 in. column base
* Column fasteners: 1/2 in. dia. machine bolts
* For full loads minimum side cover required is 2 in.
* CB column base is made for columns and posts that require high structural values and rugged performance
* Helps reduce uplift
Brand Name: Simpson Strong-Tie
*Height: 16.69 in.
*Width: 3.94 in.
*Gauge: 7 Ga.
*Material: Galvanized Steel
*Product Type: Column Base
*Minimum Heel Height: 7-5/8 in.
*Use all specified fasteners
* For full loads, minimum side cover required is 3 in. for CB, 2 in. for LCB
* Install all models with bottom of base plate flush with concrete
* Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or unbraced carports)
Brand Name: Simpson Strong-Tie
*Height: 10.44 in.
*Width: 2.19 in.
*Gauge: 16 Ga.
*Material: Galvanized Steel
*Product Type: Coiled Strap
*Assembled Width: 1-1/4 in.
*25 ft. L
* Use all specified fasteners
* Wood shrinkage after strap installation across horizontal wood members may cause strap to buckle outward
* Refer to the applicable code for minimum nail penetration and minimum wood edge and end distances
* The table shows the maximum allowable loads and the nails required to obtain them
* The cut length of the strap shall be equal to twice the "end length" noted in the table plus the clear span dimension
Brand Name: Simpson Strong-Tie
*Height: 10.31 in.
*Width: 3.56 in.
*Gauge: 12 Ga.
*Material: Steel
*Product Type: Elevated Post Base
*Assembled Width: 3-9/16 in.
*Assembled Height: 2-5/16 in.
*The elevated base plate allows 1 to 2-1/2 in. clearance above concrete
* 1-1/16 in. O.D. x 8 in. pipe
* Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or unbraced carports)
Brand Name: Simpson Strong-Tie
*Height: 4 in.
*Width: 4 in.
*Gauge: 18 Ga.
*Material: Galvanized Steel
*Product Type: Hurricane Tie
*Joist Fasteners: 8d
*Assembled Width: 5-1/4 in.
*Assembled Height: 5-1/4 in.
*Provides resistance to uplift & lateral forces, designed to help counter the effect of high wind & seismic events on a structures
* Can be installed with flanges facing inwards
* Galvanized for extra corrosion resistance
Brand Name: Simpson Strong-Tie
*Height: 6 in.
*Width: 1.69 in.
*Gauge: 18 Ga.
*Material: Galvanized Steel
*Product Type: Hurricane Tie
*Assembled Width: 1-3/8 in.
*Joist Fasteners: 8d
*Provide a positive connection between truss/rafter and the wall of the structure to resist wind and seismic forces
* Features a G90 Galvanized finish for added corrosion resistance and requires the use of hot-dip galvanized fasteners which meet the specifications of ASTM A153
Brand Name: Simpson Strong-Tie
*Height: 4.63 in.
*Width: 1.69 in.
*Gauge: 18 Ga.
*Material: Galvanized Steel
*Product Type: Hurricane Tie
*Joist Fasteners: 8d
*Designed to provide a connection between trusses/rafters and the top plate of the wall to resist high-wind/seismic forces
* Also suitable for connecting 2x deck joists on top of a perpendicular beam
* Install in pairs on either side of the rafter/truss/joist to provide resistance to uplift and lateral forces
* Use also for a variety of connections where one member crosses another
* Install with 8d common nails
Brand Name: Simpson Strong-Tie
*Height: 8 in.
*Width: 0.13 in.
*Gauge: 12 Ga.
*Material: Steel
*Product Type: Strap
*Joist Fasteners: 10d
*Assembled Width: 1-3/8 in.
*Provides the correct thickness and number of fasteners the specifier is looking for compared with field fabricated straps
* Designed for use on the edge of 2x members, with a nailing pattern that reduces the potential for splitting
* Features a G90 galvanized finish for added corrosion resistance and requires the use of hot-dip galvanized fasteners which meet the specifications of ASTM A153
Brand Name: Simpson Strong-Tie *Finish: Galvanized *Material: Steel *Product Type: Truss Clip *Frame Size: 1-1/4 in. *Number in Package: 200 *Gauge: 18 Ga. *Packaging Type: Boxed *Length: 2.7 in. *Fasteners: base 2-8d, slot 1-8d* Used for alignment control between a roof truss and nonbearing walls* The 1-1/2 in. slot permits vertical truss chord movement when loads are applied